Which fhrp implementation is a cisco proprietary protocol that supports ipv4 load sharing
|
IP routing redundancy is designed to allow for transparent fail-over at the first-hop IP router. Show
Both HSRP and VRRP enable two or more devices to work together in a group, sharing a single IP address, the virtual IP address. The virtual IP address is configured in each end user's workstation as a default gateway address and is cached in the host's Address Resolution Protocol (ARP) cache. In an HSRP or VRRP group, one router is elected to handle all requests sent to the virtual IP address. With HSRP, this is the active router. An HSRP group has one active router, at least one standby router, and perhaps many listening routers. A VRRP group has one active router and one or more backup routers. 53. What is a result when the DHCP servers are not operational Get answer to your question and much more in a network?54. A company uses the method SLAAC to configure IPv6 Get answer to your question and much more addresses for the workstations of the employees. A networkadministrator configured the IPv6 address on the LAN interfaceof the router. The interface status is UP. However, theworkstations on the LAN segment did not obtain the correctprefix and prefix length. What else should be configured on therouter that is attached to the LAN segment for theworkstations to obtain the information? Get answer to your question and much more Organizations use various protocols to prevent a single point failure in their networks. One of these protocols is the First Hop Redundancy Protocol (FHRP) which presents a virtual default gateway to the organization’s network to provide a near 100 percent network uptime. This article will look at how FHRP is used to achieve redundancy in networks, variety of FHRP, and then configure Hot Standby Redundancy Protocol (HSRP), a Cisco proprietary protocol used to implement FHRP. Table of contents
GoalsAt the end of this article, the reader is expected to learn:
PrerequisiteTo better understand this article, the reader is expected to have a basic understanding of the Cisco Command Line Interface (CLI). RequirementsWe will use the Cisco packet tracer software for this tutorial which one can download at Download Packet Tracer Default gatewayIn a network environment, devices must communicate with each other within the network and outside the network. A device that communicates with other devices outside its network or subnet requires a default gateway. A default gateway is a network node that allows seamless communication between networks, allowing one device to communicate with another on a different network or subnet. It is the first route taken by an Internet Protocol (IP) packets to ensure that internet requests are sent to the right destination. The node serving as a default gateway is configured with an Internet Protocol (IP) address. Each client in the network or subnet is configured with the same IP address. Because of this, if the router or the layer three switch serving as a default gateway fails, all devices connected to it will be isolated from the outside network. To mitigate such failures from occurring, the First Hop Redundancy Protocol (FHRP) was developed. First Hop Redundancy Protocol (FHRP)FHRP is used to prevent network failure at a default gateway. This is achieved by configuring multiple routers with the same IP address and Mac address, thus presenting an illusion of a single virtual router to the hosts in a Local Area Network (LAN). The IP address of the virtual router is configured on all hosts in that network or subnet as their default gateway. When an IP packet is sent from host devices on that network, the host uses Address Resolution Protocol (ARP) to resolve the MAC address associated. Any physically active router processes the packet sent to this MAC address within the router group. By doing so, if one router goes down, the IP packet will be processed and forwarded by the next active router. FHRP uses a mechanism known as First Hop Redundancy to determine which router takes an active role in forwarding traffic and when a standby router should take over this active role. Various First Hop Redundancy ProtocolsThere are various First Hop Redundancy Protocols available. Some of these protocols are proprietary, while others are standard protocols. Host Standby Router Protocol (HSRP)HSRP is a Cisco Proprietary FHRP that uses a large set of routers known as standby group or HSRP group to present the illusion of a single virtual router to a host. In this standby group, a single router is elected to take over as the active router if the active router fails. HSRP active and standby routers send periodic HSRP messages once the election process has been completed. HSRP featuresHSRP uses both active and standby routers to make a failover seamless in a network, thus providing better redundancy. HSRP uses the numerically highest IPv4 address as the active router to determine the active and standby router. HSRP uses the “HSRP priority” option to determine the active router for better control of the election. The router configured with the highest priority value is elected as the active router. Still, in a situation whereby all routers have equal priorities, the router with the highest numerical IP address will be the Active router. HSRP preemptionAn active router is first elected using the priority value configured on the routers and then by the IP address. In each situation, a higher value is of greater priority. A router elected as the active router will continue to function as the active router even when a new router with a higher priority value and IP address comes online. This makes it impossible for the newly added router to take over the processing and forwarding of IP packets. To enable a new election process, the standby preempts interface command is used. Gateway Load Balancing Protocol (GLBP)Gateway Load Balancing Protocol, just like Hot standby routing protocol, is a proprietary protocol that provides gateway redundancy while supporting load balancing over multiple routers (gateway). In GLBP, all routers in the GLBP group share the same virtual IP address but uses different MAC addresses with all the virtual routers participating in the forwarding of packets. ICMP Router Discovery Protocol (IRDP)IRDP is a legacy FHRP that uses Internet Control Message Protocol (ICPM) to allow hosts to discover routers on their network using router advertisement message to provide IPv4 connectivity to other non-local IPv4 networks. IRDP does not provide authentication to its advertisement messages; thus, the protocol is insecure as hosts running IRDP can be spoofed. Steps to configuring HSRPWhen configuring HSRP on a Cisco router, the following steps are used:
Configuring HSRP protocol on a Cisco routerThe topology above will be used to configure HSRP for a better understanding of this tutorial. To configure HRSP on the active router, the following steps are used:
The image above shows the configuration of an active router. Configuring HSRP on the standby routerThe following steps are used to configure a standby router.
This router takes over the forwarding of the packet only when the active router fails.  The image above shows the configuration of a standby router. To summarize, the reader has learned the following:
ConclusionHaving a network with a good uptime help organization offer effective services to their customers. Various redundant protocols have been developed and are being implemented to ensure the availability of these services. Organizations should use a protocol like FHRP to help reduce the rate of network downtime to provide effective services. Activity fileThe readers can access the configuration file used for this tutorial from this Github repository Activity File. Happy coding! Further reading
Peer Review Contributions by: Lalithnarayan C Which FHRP implementation is a Cisco proprietary protocol that Suppports ipv4 load?GLBP or Gateway Load Balancing Protocol is also a Cisco-proprietary protocol that works like HSRP and VRRP but overcomes the limitation of existing FHRPs by adding a load balancing mechanism. VRRP or Virtual Router Redundancy Protocol is a form of FHRP or First Hop Redundancy Protocol.
What protocol that supports IPv6 load sharing?The IPv6 route table selects the best route to a given destination from among the routes in the tables maintained by the configured routing protocols (BGP4, OSPF, static, and so on). The IPv6 route table can contain more than one path to a given destination.
|
